|
FAQs | Parts | Service | Store | Newsletter | Sitemap | Beer | Home |
ApplianceGuru.com: The Samurai Appliance Repair Forums > Do-It-Yourself Appliance Repair Help > The Laundry Appliance Repair Forum > K/M washer 110.23812100 |
|
FAQs | Parts | Service | Store | Newsletter | Sitemap | Beer | Home |
ApplianceGuru.com: The Samurai Appliance Repair Forums > Do-It-Yourself Appliance Repair Help > The Laundry Appliance Repair Forum > K/M washer 110.23812100 |
Konnichiwa and Welcome!Please register or watch this short screencast on how to get started here.
|
| Moderated by: RegUS_PatOff, Pegi |
|
|
|||||||||||||
| K/M washer 110.23812100 | Rate Topic |
| Author | Post |
|---|
| Posted: Wed Oct 14th, 2009 06:16 pm |
|
1st Post |
|
certified tech group 51 Sublime Master of Appliantology 
|
Went to customers house, the complaint was ' not spinning out every time'. By-passed the lid switch, put unit into spin, slow start in spin..stopped spin cycle, restarted spin cycle, at the start of spin, I could stall the basket from spinning......The customer was watching and asked what the problem was.....I said that it could be oil on the clutch and it was slipping..... Tipping the unit back, I could not see any oil from the trans. on the clutch or on the outer wrapper.......So propping the washer onto the toilet I replaced the clutch, tested in spin, difficult to stall in the spin cycle...... About five days later, the customer called and said that it was not spinning out again.....Went out there and he had left the load 'as is', load in the bottom and had not spun -out....Set the timer to spin, it spun.... Looking at the tech sheet, looked for a spin cycle..... moved the timer manually and when it got close for the motor to pause for the spin pawl to be activated, I held the timer dial for about 10 seconds...The timer advanced from start to finish with-out a pause. See motor contacts  .........SO, the customer was upset that he paid for repair that wasn't really needed, I ordered a timer, installed it for free ( parts and labor )..That way the customer had NOTHING to complain about....... So techs here is another item to check for the complaint of "Not spinning out every time"..... Sorry for the fonts, could not fix, so it sounds like a 6 year old wrote this, I tried to fix it, but made it worse.....
|
||||||||||||||
| |||||||||||||||
| Posted: Wed Oct 14th, 2009 06:30 pm |
|
2nd Post |
|
RegUS_PatOff Fellow, Academy of Sublime Masters of Appliantology 
|
always make sure the water has pumped out before Spin ... (Neutral Drain feature) then Timer pauses for 2 seconds to re-engage the Spin
____________________ RegUS_PatOff http://www.youtube.com/watch?v=oPAY2LsKVEw my video production: “Easter Seals Walk With Me” (also in HQ) http://www.youtube.com/watch?v=-EBiLyYXMiA Upon leaving this Earth "Do you want the Smoking or Non-Smoking section ?" |
|||||||||||||
| ||||||||||||||
| Posted: Thu Oct 15th, 2009 05:00 am |
|
3rd Post |
|
certified tech group 51 Sublime Master of Appliantology
|
On the cam chart marked with red dot , on the left, the diamond mark..'indicates motor off'....in the second picture, the motor contacts welded themselves together ( contacts on the left, on the right are good contacts ) ......so the motor did not pause, it stayed in drain the full duration....According to the customer it only happened in this cycle, red dots on cam chart...I am surmising that the cam could not break the welded contact ...I.E. no spin problems in the other cycles .......
|
||||||||||||||
| |||||||||||||||
| Posted: Sat Oct 31st, 2009 06:28 pm |
|
4th Post |
|
appl.tech.29501 Fellow, Academy of Sublime Masters of Appliantology 
|
yep seen that 1 happen a few times....fooled me first time too 
____________________ If you would like to make a donation you may do so at the link below http://homepage.mac.com/zenzoidman/appl.tech.29501/ |
|||||||||||||
| ||||||||||||||
| Posted: Sat Oct 31st, 2009 07:52 pm |
|
5th Post |
|
Samurai Appliance Repair Man Fermented Grand Master of Appliantology 
|
Good war story, CTG. Great reminder for all of us. Domo for posting it!
____________________ Links: Parts | FAQs | Store | Beer | Home |
||||||||||||||
| |||||||||||||||
| Current time is 08:11 pm | |
| ApplianceGuru.com: The Samurai Appliance Repair Forums > Do-It-Yourself Appliance Repair Help > The Laundry Appliance Repair Forum > K/M washer 110.23812100 | Top |
FAQs | Parts | Service | Store | Newsletter | Sitemap | Beer | Home
