|
FAQs | Parts | Service | Store | Newsletter | Sitemap | Beer | Home |
ApplianceGuru.com: The Samurai Appliance Repair Forums > Do-It-Yourself Appliance Repair Help > The Laundry Appliance Repair Forum > Gas Dryer Heat Problems. |
|
FAQs | Parts | Service | Store | Newsletter | Sitemap | Beer | Home |
ApplianceGuru.com: The Samurai Appliance Repair Forums > Do-It-Yourself Appliance Repair Help > The Laundry Appliance Repair Forum > Gas Dryer Heat Problems. |
Konnichiwa and Welcome!Please register or watch this short screencast on how to get started here.
|
| Moderated by: RegUS_PatOff, Pegi |
|
|
|||||||||||||
| Gas Dryer Heat Problems. | Rate Topic |
| Author | Post |
|---|
| Posted: Mon Jun 29th, 2009 02:03 am |
|
1st Post |
|
vinmoe Apprentice Appliantologist, First Class
|
I have a Kenmore Gas Dryer (76923692) and it started not getting very hot. No matter what setting it was on (besides air) the flame would go on/off all the time but never stay on long enough to get very hot. It would take 2 hours to dry a small load. I replaced the hi and low thermostats and it still did the same thing. Then just for fun I removed the hi thermostat and the dryer now gets too hot. If the temperature dial is on any setting except air the dryer gets too. Hot when it is on air the flame does stay off. I have attached the schematic and any assistance would be helpful. I also did remove the vent hose and that did not help. This is the first of the help forum I belong to that requires a fee to post but I will be very happy if I get the correct answer to fix this. Thanks, Jeff Oregon Attachment: schematic_Page_2.jpg (Downloaded 23 times)
|
||||||||||||||
| |||||||||||||||
| Posted: Mon Jun 29th, 2009 02:27 am |
|
2nd Post |
|
RegUS_PatOff Fellow, Academy of Sublime Masters of Appliantology 
|
If it no longer shuts off too soon after bypassing the Hi-Limit Thermostat, then it's either bad, or there's not enough air-flow. Check the Lint Screen and check the air-flow out the Vent Also check the model number again, should be 110.xxxxxxxx
____________________ RegUS_PatOff http://www.youtube.com/watch?v=oPAY2LsKVEw my video production: “Easter Seals Walk With Me” (also in HQ) http://www.youtube.com/watch?v=-EBiLyYXMiA Upon leaving this Earth "Do you want the Smoking or Non-Smoking section ?" |
|||||||||||||
| ||||||||||||||
| Posted: Mon Jun 29th, 2009 03:56 am |
|
3rd Post |
|
vinmoe Apprentice Appliantologist, First Class
|
The instructions for this forum said to leave out the 110. that's why I did not post it. The full # is 110.76932692. I already replaced the hi and low thermostat and that did not do it. I checked the continuity of both and they look OK. There is no problem with airflow as the back of the dryer put out lots of air. Lint screens and the venting has all been cleaned and the air flow to the outside is fine.
|
||||||||||||||
| |||||||||||||||
| Posted: Mon Jun 29th, 2009 04:49 am |
|
4th Post |
|
RegUS_PatOff Fellow, Academy of Sublime Masters of Appliantology
|
vinmoe wrote: The instructions for this forum said to leave out the 110. that's why I did not post it. What instructions... I thought I tried 110.76932692 .. oh well.. Not much else it could be... Dryer Vent Vent should be rigid metal. Short lengths of flexible metal may be OK, if not crimped when moving the Dryer into place. NO plastic NO PVC NO screws Foil Duct Tape is OK. With an empty load, Timed Dry, High Heat, the vent temperature should cycle somewhere between 135F and 160F
____________________ RegUS_PatOff http://www.youtube.com/watch?v=oPAY2LsKVEw my video production: “Easter Seals Walk With Me” (also in HQ) http://www.youtube.com/watch?v=-EBiLyYXMiA Upon leaving this Earth "Do you want the Smoking or Non-Smoking section ?" |
|||||||||||||
| ||||||||||||||
| Posted: Mon Jun 29th, 2009 07:34 am |
|
5th Post |
|
vinmoe Apprentice Appliantologist, First Class
|
how do I measure the temperature?
|
||||||||||||||
| |||||||||||||||
| Posted: Mon Jun 29th, 2009 07:42 am |
|
6th Post |
|
RegUS_PatOff Fellow, Academy of Sublime Masters of Appliantology
|
If you have a Harbor Freight store near you click on picture $ 2.99 
____________________ RegUS_PatOff http://www.youtube.com/watch?v=oPAY2LsKVEw my video production: “Easter Seals Walk With Me” (also in HQ) http://www.youtube.com/watch?v=-EBiLyYXMiA Upon leaving this Earth "Do you want the Smoking or Non-Smoking section ?" |
|||||||||||||
| ||||||||||||||
| Posted: Tue Jun 30th, 2009 03:43 am |
|
7th Post |
|
vinmoe Apprentice Appliantologist, First Class
|
I have one of those but if I put it in the dryer it will bounce around and break.
|
||||||||||||||
| |||||||||||||||
| Posted: Tue Jun 30th, 2009 03:56 am |
|
8th Post |
|
Samurai Appliance Repair Man Fermented Grand Master of Appliantology 
|
vinmoe wrote:I have one of those but if I put it in the dryer it will bounce around and break. Dayyam, so that's why I can't measure dryer temperatures!  Maybe instead of inside the dryer, we push it through the dryer vent, right behind the exhaust port.
____________________ Links: Parts | FAQs | Store | Beer | Home |
|||||||||||||
| ||||||||||||||
| Posted: Tue Jun 30th, 2009 04:39 am |
|
9th Post |
|
RegUS_PatOff Fellow, Academy of Sublime Masters of Appliantology
|
RegUS_PatOff wrote: ... the vent temperature should cycle somewhere between 135F and 160F...
____________________ RegUS_PatOff http://www.youtube.com/watch?v=oPAY2LsKVEw my video production: “Easter Seals Walk With Me” (also in HQ) http://www.youtube.com/watch?v=-EBiLyYXMiA Upon leaving this Earth "Do you want the Smoking or Non-Smoking section ?" |
||||||||||||||
| |||||||||||||||
| Current time is 08:56 pm | |
| ApplianceGuru.com: The Samurai Appliance Repair Forums > Do-It-Yourself Appliance Repair Help > The Laundry Appliance Repair Forum > Gas Dryer Heat Problems. | Top |
FAQs | Parts | Service | Store | Newsletter | Sitemap | Beer | Home
