|
FAQs | Parts | Service | Store | Newsletter | Sitemap | Beer | Home |
ApplianceGuru.com: The Samurai Appliance Repair Forums > Do-It-Yourself Appliance Repair Help > The Laundry Appliance Repair Forum > Maytag Washer MAH21PDAWQ S# 25698140CC |
|
FAQs | Parts | Service | Store | Newsletter | Sitemap | Beer | Home |
ApplianceGuru.com: The Samurai Appliance Repair Forums > Do-It-Yourself Appliance Repair Help > The Laundry Appliance Repair Forum > Maytag Washer MAH21PDAWQ S# 25698140CC |
Konnichiwa and Welcome!Please register or watch this short screencast on how to get started here.
|
| Moderated by: RegUS_PatOff, Pegi |
|
|
|||||||||||||
| Maytag Washer MAH21PDAWQ S# 25698140CC | Rate Topic |
| Author | Post |
|---|
| Posted: Sun Jun 14th, 2009 07:51 pm |
|
1st Post |
|
avdelgado Chief Apprentice Appliantologist
|
Machine tumbles but does not spin up to full speed. I troubleshot IAW Maytag service manual and replaced motor control board from known good machine. Worked fine for a week but now has same problem. Measured motor windings, found them good according to service manual. Measured tach output from motor pins 4 & 5 and found them open, service manual calls for 155-195 ohms. Maytag service manual troubleshooting tree does not address this condition. Is the tach output required for operation or is it used as part of the help mode that provides failure codes? No diagnostic (failure) codes given when using service mode. 
____________________ Andy Delgado |
||||||||||||||
| |||||||||||||||
| Posted: Sun Jun 14th, 2009 08:24 pm |
|
2nd Post |
|
RegUS_PatOff Fellow, Academy of Sublime Masters of Appliantology 
|
What's the results of the Troubleshooting Flowchart on PDF page 90 ? MAH21PDAWQ Service Manual Does this have the updated Motor/Controller ? 
____________________ RegUS_PatOff http://www.youtube.com/watch?v=oPAY2LsKVEw my video production: “Easter Seals Walk With Me” (also in HQ) http://www.youtube.com/watch?v=-EBiLyYXMiA Upon leaving this Earth "Do you want the Smoking or Non-Smoking section ?" |
|||||||||||||
| ||||||||||||||
| Posted: Sun Jun 14th, 2009 11:52 pm |
|
3rd Post |
|
avdelgado Chief Apprentice Appliantologist
|
RegUS_Patoff, Thanks for the quick reply. The machine does have the updated motor/harness and motor control board installed. Hopefully, my sister/brother in-law will be able to test using the flow chart as recommended tonight.
____________________ Andy Delgado |
||||||||||||||
| |||||||||||||||
| Posted: Fri Jul 3rd, 2009 02:57 am |
|
4th Post |
|
avdelgado Chief Apprentice Appliantologist
|
RegUS_Patoff, The machine did have the updated motor and control board. You would not believe it. There was enough change left in the machine from someones pockets that it got past the pump and clogged the output hose. There were no error codes that pointed to slow drain. Anyway, there was so much change in the outlet hose that I had to drive it all out with a pipe. Machine works like a champ now. 
____________________ Andy Delgado |
|||||||||||||
| ||||||||||||||
| Posted: Fri Jul 3rd, 2009 03:10 am |
|
5th Post |
|
RegUS_PatOff Fellow, Academy of Sublime Masters of Appliantology
|
____________________ RegUS_PatOff http://www.youtube.com/watch?v=oPAY2LsKVEw my video production: “Easter Seals Walk With Me” (also in HQ) http://www.youtube.com/watch?v=-EBiLyYXMiA Upon leaving this Earth "Do you want the Smoking or Non-Smoking section ?" |
||||||||||||||
| |||||||||||||||
| Current time is 08:42 pm | |
| ApplianceGuru.com: The Samurai Appliance Repair Forums > Do-It-Yourself Appliance Repair Help > The Laundry Appliance Repair Forum > Maytag Washer MAH21PDAWQ S# 25698140CC | Top |
FAQs | Parts | Service | Store | Newsletter | Sitemap | Beer | Home
