|
FAQs | Parts | Service | Store | Newsletter | Sitemap | Beer | Fixitnow.com |
ApplianceGuru.com: The Samurai Appliance Repair Forums > Do-It-Yourself Appliance Repair Help > The Kitchen Appliance Repair Forum > L2 Burns up on Frigidiare oven PLES389ACC |
Konnichiwa and Welcome!Please register to post a question. It's FREE!
|
| Moderated by: RegUS_PatOff, Pegi, appl.tech.29501 |
|
|
|||||||||||||
| L2 Burns up on Frigidiare oven PLES389ACC | Rate Topic |
| Author | Post |
|---|
| Posted: Tue Nov 17th, 2009 02:27 pm |
|
1st Post |
|
ifixit Merit Apprentice Appliantologist
|
I fixed a bad L2 connection (new cord and wire repair and terminal block) 2 weeks later it burned up again at the terminal block..(same problem) connections on burner sw's look good, can't figure out what I am missing here...examined whole harness for problems and found nothing obvious. Is this unit under recall? What is the correct amp draw for these burners? Thanks Dave _________________ David Hinton DBH Appliance Repair Last edited on Tue Nov 17th, 2009 02:28 pm by ifixit |
||||||||||||||
| |||||||||||||||
| Posted: Tue Nov 17th, 2009 06:02 pm |
|
2nd Post |
|
RegUS_PatOff Fellow, Academy of Sublime Masters of Appliantology 
|
If it drew too much current, it should've blown the House Breakers. It may be the (now) tarnished Range Ring Terminal that connects to the Terminal Strip and Power Cord. If copper overheats, it gets tarnished and is no longer a good conductor and should be replaced.
____________________ RegUS_PatOff http://www.youtube.com/watch?v=oPAY2LsKVEw my video production: “Easter Seals Walk With Me” (also in HQ) http://www.youtube.com/watch?v=-EBiLyYXMiA Upon leaving this Earth "Do you want the Smoking or Non-Smoking section ?" |
|||||||||||||
| ||||||||||||||
| Posted: Tue Nov 17th, 2009 07:20 pm |
|
3rd Post |
|
ifixit Merit Apprentice Appliantologist
|
cord, terminal block , and l2 connector were all new on 1st repair
|
||||||||||||||
| |||||||||||||||
| Posted: Tue Nov 17th, 2009 08:12 pm |
|
4th Post |
|
RegUS_PatOff Fellow, Academy of Sublime Masters of Appliantology
|
all the wires (terminals) on the L2 Terminal ?
____________________ RegUS_PatOff http://www.youtube.com/watch?v=oPAY2LsKVEw my video production: “Easter Seals Walk With Me” (also in HQ) http://www.youtube.com/watch?v=-EBiLyYXMiA Upon leaving this Earth "Do you want the Smoking or Non-Smoking section ?" |
|||||||||||||
| ||||||||||||||
| Posted: Tue Nov 17th, 2009 10:09 pm |
|
5th Post |
|
ifixit Merit Apprentice Appliantologist
|
Only 1 wire went to l2 term on term block, new. new term block and new cord....all new
|
||||||||||||||
| |||||||||||||||
| Posted: Wed Nov 18th, 2009 03:30 am |
|
6th Post |
|
Samurai Appliance Repair Man Fermented Grand Master of Appliantology 
|
Electrical connections burn because 1) too much current draw for the connection or 2) the connection was loose. Like Reg said, if it was drawing too much current, the breaker woulda tripped... assuming the breaker is the correct size, no larger than 30 amps. That leaves loose connection, nut not tightened down enough.
____________________  If I've helped you with your repair, please consider supporting my flavorite charity: http://beer.fixitnow.com |
|||||||||||||
| ||||||||||||||
| Current time is 09:20 am | |
| ApplianceGuru.com: The Samurai Appliance Repair Forums > Do-It-Yourself Appliance Repair Help > The Kitchen Appliance Repair Forum > L2 Burns up on Frigidiare oven PLES389ACC | Top |
FAQs | Parts | Service | Store | Newsletter | Sitemap | Beer | Fixitnow.com
