|
FAQs | Parts | Service | Store | Newsletter | Sitemap | Beer | Fixitnow.com |
ApplianceGuru.com: The Samurai Appliance Repair Forums > Do-It-Yourself Appliance Repair Help > The Kitchen Appliance Repair Forum > Another Bosch SHU4302 Question |
|
FAQs | Parts | Service | Store | Newsletter | Sitemap | Beer | Fixitnow.com |
ApplianceGuru.com: The Samurai Appliance Repair Forums > Do-It-Yourself Appliance Repair Help > The Kitchen Appliance Repair Forum > Another Bosch SHU4302 Question |
Konnichiwa and Welcome!Please register to post a question. It's FREE!
|
| Moderated by: RegUS_PatOff, Pegi, appl.tech.29501 |
|
|
|||||||||||||
| Another Bosch SHU4302 Question | Rate Topic |
| Author | Post |
|---|
| Posted: Sat Nov 14th, 2009 09:51 pm |
|
1st Post |
|
Dubyacee Grasshopper
|
I have the usual problem of long run time and undried dishes. Previously ( 2 yrs ago) repaired the solder joint on the board. I checked the current with amprobe and it is 2 amps or so, which verifies a problem with the heater. How can I check further before replacing the control board or disassembling the washer to get at the heater? Can the heater and associated switches be tested from the front? What are the chances that the heater and/or thermostat switch is bad? I am electrically savvy but don't relish taking the beast apart unless absolutely unavoidable. Oh wise and fearless one - what to do?
|
||||||||||||||
| |||||||||||||||
| Posted: Sat Nov 14th, 2009 10:02 pm |
|
2nd Post |
|
RegUS_PatOff Fellow, Academy of Sublime Masters of Appliantology 
|
Did you check the solder joints again ? Do you have / need the Service Manual ?
____________________ RegUS_PatOff http://www.youtube.com/watch?v=oPAY2LsKVEw my video production: “Easter Seals Walk With Me” (also in HQ) http://www.youtube.com/watch?v=-EBiLyYXMiA Upon leaving this Earth "Do you want the Smoking or Non-Smoking section ?" |
|||||||||||||
| ||||||||||||||
| Posted: Sun Nov 15th, 2009 03:00 pm |
|
3rd Post |
|
Dubyacee Grasshopper
|
Yes, the solder connection was the first place I looked. Would the service manual address my questions on how to isolate the problem? The test procedures are readily available but no instructions on how/where to measure the resistance of the heater element and other devices. I see that others have replaced the control board and not cure the problem so I would like to be more sure before going there.
|
||||||||||||||
| |||||||||||||||
| Posted: Sun Nov 15th, 2009 04:00 pm |
|
4th Post |
|
RegUS_PatOff Fellow, Academy of Sublime Masters of Appliantology
|
βởşčĥ щΐяîйģ ₫їẵğяǻмš ặяз ήỗŧởѓỉọữşŁỷ ςяўÞťĩç service manual link PM'd
____________________ RegUS_PatOff http://www.youtube.com/watch?v=oPAY2LsKVEw my video production: “Easter Seals Walk With Me” (also in HQ) http://www.youtube.com/watch?v=-EBiLyYXMiA Upon leaving this Earth "Do you want the Smoking or Non-Smoking section ?" |
|||||||||||||
| ||||||||||||||
| Current time is 12:08 pm | |
| ApplianceGuru.com: The Samurai Appliance Repair Forums > Do-It-Yourself Appliance Repair Help > The Kitchen Appliance Repair Forum > Another Bosch SHU4302 Question | Top |
FAQs | Parts | Service | Store | Newsletter | Sitemap | Beer | Fixitnow.com
